Sennheiser EM 6000 2-Channel Digital Receiver

Combining elite signal reliability with higher channel density, the Sennheiser EM 6000 is an intermodulation-free 2-channel digital receiver that fits snugly within a 1U rack-mounting chassis.

Showcasing the finest in receiver technology, the EM 6000 amalgamates two receiver paths to ensure optimised reception and less chance of dropout. Not only that but the built-in Audinate Brooklyn II card provides Dante connectivity, so you can effortlessly integrate into a new or pre-existing DANTE network.

Sennheiser EM 6000 2-channel Digital Receiver Specifications:

Audio output

• Dante, RJ-45: 48 kHz, 96 kHz, 24 bit
• Digital Audio outputs: AES3-2003, XLR-3: 48 kHz, 96 kHz, 24 bit
• Dante, RJ-45: 48 kHz, 96 kHz, 24 bit
• Can be externally synchronized using WCLK loop-through with BNC sockets
• Analog Audio Outputs: XLR-3 and 6.3 mm jack per channel (transformer balanced)
• -10 dBu to +18 dBu in steps of 1 dB (2 kO)
• Dimensions: 44 x 483 x 373 mm
• Frequency response: 30 Hz - 20 kHz (1.5 dB)
• THD, total harmonic distortion: < 0.03 % (@ 1 kHz)
• Weight: Approx. 5.2 kg
• Power consumption: Max. 35 W
• Storage temperature: -25°C to +70°C
• Operating temperature: -10°C to +50°C
• Switching bandwidth: 244 MHz
• Power supply: 100 - 240 V AC, 50/60 Hz

 Antenna connector:

• Input 2x BNC (50 O), 12 V DC, max. 200 mA each via antenna sockets, short circuit proof, Output 2 x BNC (50 O)

• Codecs: SePAC (Sennheiser Performance Audio Codec)
• Dynamic range: 111 dB (A) type
• Frequency range: 470 - 714 MHz
• Headphone output level: 6.3 mm jack, 2x 100 mW at 32 O
• Image rejection: > 100 dB typ.
• Sensitivity: -100 dBm typ.

Word clock:

• Input: BNC, 75 O
• Output: BNC, 75 O
• Sampling Rates: 48 kHz, 96 kHz

 
Operating relative humidity:

• Operation: Max. 85% at 40°C (non-condensing)
• Storage: Max. 90% at 40°C (non-condensing)

• Transmission method: Digital modulation, “LR” mode Min. frequency spacing for equidistant grid: 325 kHz

 
Latency:

• Analog Audio Out: 3 ms
• Digital Audio Out: 3 ms (AES/EBU)

• Audio codec: SeDAC (Sennheiser Digital Audio Codec)
• Network protocol: IEEE 802.3-2002 (10/100 Mbit/s), shielded RJ-45 connection
• Receiver Principle: Double superheterodyne
• Diversity principle: True bit diversity
• Encryption: AES 256
• Daisy chain outputs: 2x BNC (50 O) 0 dB +/- 0.5 dB amplification relative to antenna inputs
• Receiving channels: 2
• Daisy-chained receivers (RF): Max. 8 EM 6000 units
• Power plug: 3-pin, protection class I as per IEC/EN 60320-1
• Water Protection Code: The product must not be exposed to dripping and splashing (IP2X)
• Dante: IEEE 802.3 (1000 Mbit/s), shielded RJ-45 connection